009716 – Pro Series II™ Star Orbiter™

(7 customer reviews)

$24.99

Pro Series II Builder Kit

45 inches tall! E16-6 and F15-8 engine powered!

ATTENTION: Requires PS II Launch Base (3552) with 1/4″ launch rod or Porta-Pad E Launch Pad (2238) and E Launch Controller (2230) or Pro Series II Launch Controller (2240) with 30′ of wire – Sold Separately

Download Instructions

In stock

Share with your friends!
  •  
  •  
  • 2
  •  

Description

Pro Series II

We continue to develop and grow the Pro Series II line! This time around we’re offering up a BT60 (1.64 in/42 mm) diameter body tube for your building enjoyment. Standing over 45 inches tall, the Star Orbiter comes with the quick release motor retention system just as the other Pro Series kits do. (9750 Pro Series II 29MM Retainer Set – is also sold separately). Construction of this kit is not difficult and the altitudes you will reach are very impressive! Building and finish work can easily be accomplished over a few days.

WHAT YOU NEED TO BUILD: Scissors, pencil, ruler, fine sandpaper, epoxy, carpenter’s glue, hobby knife, masking tape, clear tape, primer (white), paint (black, orange) and clear coat (optional). (Tools, construction and finishing supplies not included.)

WHAT YOU NEED TO LAUNCH (sold separately): Pro Series II Launch Base and Pro Series II Launch Controller, Estes model rocket engines, starters and Pro Series II Recovery Wadding. Six C 1.5V high quality alkaline batteries are also required for launch controller (not included).


WarningWARNING

Additional information

Projected Max Altitude

1800 ft. (549 m)

Recovery System

18 in. (45.7 cm) Parachute

Length

45.2 in. (114.8 cm)

Diameter

1.64 in. (42 mm)

Estimated Weight

5.9 oz. (167.3 g)

Estimated Assembly Time

2 Hours (painting and glue drying time not included)

Construction

Screw on Motor Retainer

Fin Materials

Laser cut wood

Decal Type

Waterslide

Launch System

Pro Series II Launch Pad and Pro Series II Launch Controller

Launch Rod Size

1/4"

Age Recommendation

Estes Pro Series II rocket kits are recommended for boys and girls ages 18+ with adult supervision for those under 18, and rocketeers of all ages.

7 reviews for 009716 – Pro Series II™ Star Orbiter™

  1. Tim Fritts

    WHAT TO TAKE TO THE RANGE, MY Favorite Rocket
    This one gets shoot at least rwo of three time every time I go out.I have two, one built as the kit came and the other I made a few changes.Updated the centering rings to wood and added a a piece of 750# Bonded Kevlar Shock Cord about 2x longer than the total length of the rocket and tried it around the motor mount and pulled up into the rocket body though a small hole drilled in the top wooden centering ring, tied an overhand note attached my rubber shock cord and upgraded the launch lugs to 3D Printed 1/4 inch Launch Lugs from Rocketry Works. Added a 18″ Nylon parachute from Apogee Rockets which opens fast and packs very nice. Finally, I painted it black and white and added all the decals. Use Estes E16-6, F15-6 or push it with a Areotech F26FJ-9, F50T-9, G38FJ-7
    This is a great high flier for all ages. Thanks

  2. Sine Nomine

    This rocket is built to go high – really high. It’s not a minimum diameter 29mm kit, but it’s close. That means it will hit serious altitudes even with an E. My first flight was with a D12 (using a 29-24mm adapter) and it still made it past 500′. If you’re planning on flying with composite motors, you will want to use epoxy and reinforce the fins with CA. You’ll probably want a chute release too because you’re going to be walking a long way to recover it.

  3. Jonathan Burton

    This is a fantastic rocket. Also a fantastic introduction kit to mid power for a kid who’s a little older and ready for bigger motors. I only built mine right now to be single deploy. So only baby g’s f’s and E’s i will fly this rocket on. I painted mine bright hazard orange and named it Agent orange. This rockets fins while being thick balsa are super sturdy. I absorbed super liquid super glue in them to sturdy them up, then covered them in a lot of paint. This rocket flies amazing on E12 motors as well as the f’s and g’s. I find it a little too heavy for e9’s and don’t prefer flying it on those motors.

  4. Don Allen

    This is a great mid-power rocket especially using the F and G engines. I’ve just gotten two more in preparation to make it a 2 stage using one of the kits for a booster on the BT-60 body tube. I use an ejection baffle at the mid-point. This will also serve as a stronger anchor point for the shock cord. I’ve learned from past experience to use a wider (and longer) shock cord as too-thin of a shock cord will zipper the tube. I plan on replacing the balsa wood with 1/8″ plywood and I use good old JB Weld epoxy on the motor mount. A slotted airframe would be an ideal upgrade too. I use Titebond wood glue on most parts and it makes great glue fillets for the fins. The retainer rings work well especially using the 24 to 29 mm adapter. No engine blocks needed. This design is just simply awesome. On the next kit build, it will get 1/4″ launch lugs to go on my 6″ launch rod. I find it’s easier to spot if the bottom tube is black and upper tube is red/orange.

  5. Leo

    Great flyer

    The Star Orbiter is an easy to build sleek looking rocket and is one of my favorites.
    I’ve purchased several Star Orbiters and the one I’m flying right now is converted to dual deploy recovery having it’s successful maiden flight on 5 September 2016.
    As of this writing the max altitude reached so far is 2726 feet. But it won’t stop there…
    Here a video example: https://www.youtube.com/watch?v=yPEEPmfB_r4
    And here a build thread: http://www.rocketryforum.com/showthread.php?134806-Estes-Star-Orbiter-9716

  6. Anthony

    My favorite rocket

    I love this rocket so much I cleared the shelf of them. Very simple, light weight, durable and easy to modify. It rips off the pad. I hit 2500 feet and 359 mph with a G40-7. Recommend dual deploy with ejection charge removed with this particular rocket and engine combo. This rockets decent size will allow you to keep sight of it even at high altitudes. I recommend papering the fins for added durability. Really great rocket.

  7. Louie

    looks good…

    And yet another cool looking Pro Series 2 kit I gotta have….

Add a review

Your email address will not be published. Required fields are marked *



X

1 new item has been added to your cart

X